![malvern zetasizer pricing malvern zetasizer pricing](https://media.labcompare.com/m/1/product/7558039-400x300.jpg)
- Malvern zetasizer pricing verification#
- Malvern zetasizer pricing series#
- Malvern zetasizer pricing free#
The readback lead from the Aqueous / non Aqueous Cells is connected to this connector. (8) Aqueous / non Aqueous dip cell readback connector The sample in/out connectors are used to inject the sample into the capillary and sizing flowcell. Connectors are a simple push fit, however to remove them, the clip should be pushed sideways rather that pulled. The yellow connector is clipped to the yellow electrode at the rear of the cell and obviously the red connector on the red coded electrode. The grey electrode wires are colour coded. These electrodes are connected to the electrode blocks once the capillary is fitted. The capillary cell is used to make zeta potential measurements. In the event of a large spillage a service visit by a Malvern representative is recommended.įor measurements done above ambient temperature it is recommended that the insulating thermal cover is fitted. This is to prevent spillage into the sample holder and better thermal stability. It is strongly recommended that tops are fitted to the sample cuvette prior to insertion into the cell holder. The type chosen will be dictated by chemical compatibility with the sample and dispersant.
Malvern zetasizer pricing series#
This is only applicable to the Zetasizer 10 series systems. The sizing cell is used to make size measurements. The sample valves control the flow of sample through the cell. This should not be changed in normal operation. Zetasizer 10 series) are supplied with a 200 micron pinhole fitted. When the cover is lowered completely the laser will illuminate the sample.ĭependent on the system ordered, systems incorporating size measurement (i.e. Consequently, laser radiation is inaccessible as soon as the cover is opened. There is a mechanical laser interlock connected to the cover and an electrical interlock to cut off the power supply to the cell. To access the sample compartment the cover must be raised. The illustration below identifies the features of the sample area. The right hand LED will glow green shortly after the instrument is switched on to indicate that the instrument is ready to make a measurement, it will flash red when a measurement is being made. The far left LED glows orange to indicate that power is on. Two LEDs are situated on the front panel (1). These are the front panel (1), the sample area The Zetasizer optics unit can be divided into three areas for the purposes of this description. Supplied with disposable polystyrene and glass cuvettes for size measurement.Īutomatic setting and sensing of applied voltage, temperature andġ25, 250, 500 or 1000Hz frequency. Zetasizer 3000 series Standard capillary electrophoresis cell. Zetasizer 2000 Standard capillary electrophoresis cell. Zetasizer 1000 series Supplied with disposable polystyrene and Heterodyne zetapotential, Homodyne or self beat size mode.ĭuty cycle operation limits heating in high conductivity media. (Sample and source dependent).Īpplicable size range, 5nm - 30 microns (Sample dependent). Graphical and tabular formats for particle size, electrophoreticĪnd zeta potential distributions graphical plots of any two parameters e.g.
Malvern zetasizer pricing free#
Use with a Titrator or autosampler requires two free RS232C communication ports. IBM PC-AT compatible, Pentium 166MHz processor, 32MByte RAM, specificationģ0 Mbytes free disk space, one free RS232C communications port, Zetasizer Particle Size and Zeta Potential Analyser. Please refer to the text of the offer for the exact scope of delivery.
![malvern zetasizer pricing malvern zetasizer pricing](https://3.imimg.com/data3/KG/WJ/MY-2957828/zetasizer-nano-zsp-500x500.jpg)
They do not represent the scope of delivery. The following illustrations and descriptions refer to the instrument model and are drawn from brochures. When self-collecting/ordering EXW from countries within or outside the European Union, 16% VAT will be retained as a deposit until we have received the corresponding confirmation of arrival/bill of delivery from the buyer. Note for international shipments: A proof of preference/EUR1 will not be issued by us. If transport costs are not specified, please ask separately for them.įor deliveries to countries outside the EU, an additional fee of 70,00€ for export is charged. Stated shipping costs are to be expected. Parcel services, forwarding agencies, self-pickup, delivery by Labexchange fleet. A partial delivery is possible on explicit request. The shipping time is calculated based on the position with the longest lead time. The effective dispatch times will be stated in the order confirmation.Īs a matter of principle, we are offering collective deliveries. The stated dispatch times are the shortest possible ones for each article. You are receiving only fully functional devices. The second-hand devices are verified by Labexchange Service GmbH before delivery.
Malvern zetasizer pricing verification#
Status, terms of delivery and payment Verification of devices